Are you wondering, Can you stain edge banding on veneer? There are a few different ways to finish this type of banding, including water-based wood stain and spray on polyurethane. Read on to find out which one is best for your needs. You can also use water-based paint if you want to keep it simple. Regardless of what kind of finish you choose, there are several things you must consider before you begin.
Veneer edge banding
If you want a basic straight edge for your plywood or other sheet goods, veneer edge banding may be the best option. This product is made from real wood veneer and is available in 7/8″ widths. It is a popular choice for 3/4″ thick sheet goods, as it allows for a small overhang and is easy to trim to a flush edge. Once the veneer edge banding is installed, you can stain or paint it to match your project.
When applying veneer to plywood, it is important to iron the edges gently. The veneer should be applied with a bit of pressure, but not too much. Using an iron, make sure to place it at a spot where it will not burn the wood. You can also use a wooden block to press down the edge banding as it cools. Once the adhesive has dried, trim the veneer to fit, keeping it flush with the plywood.
Once the glue is dry, cut the edge banding to fit the plywood. The edge banding should be placed flush with the top edge of the plywood. Once you’ve cut the edge banding, use a utility knife to carefully sand it to smooth out any rough edges. You can also use a sanding block to gently sand the edges to make them smooth. When applying stain, be sure to sand the pieces carefully, as they’ll have sharp edges.
Water-based wood stain
Choosing a water-based wood stain for edge banding is an easy process. Unlike oil-based stains, which contain volatile organic compounds, water-based stains dry quickly and do not cause paint stripping or other chemical agents. Water-based stains also don’t cause as much fumes and have fewer VOCs. They are also suitable for both indoor and outdoor projects because of their water-repellent properties.
Whether you’re using water-based or oil-based products, you’ll want to follow the manufacturer’s instructions to the letter. Oil-based wood stains can cause a problem if they drip on a piece of furniture. In order to avoid this, you should use a stain blocker before applying a water-based stain. While this is an option, it can’t guarantee that knots won’t show through. Light-colored paints won’t cover knots well, so dark stains are the best choice.
The final step in applying water-based wood stain is to apply wood conditioner. This will help the edge band blend with the plywood veneer. It will also prevent squeeze-out of stain during glue-up. In addition, wood conditioner is useful in preventing stain from smearing across the surface. While using water-based wood stains, make sure to follow the manufacturer’s instructions.
Spray on polyurethane
Polyurethane is a widely used surface finish, and the instructions for application usually indicate that it can be sprayed on. It’s recommended that you sand the edges of the edge banding before applying the finish. Depending on the type of polyurethane, you may use sandpaper or steel wool to abrade it. However, sandpaper is the most effective abrasive. Some manufacturers incorporate myths into their instructions, but these aren’t important. While some of the myths make sense, they actually do more harm than good. There are numerous articles in the Internet, and many of these products are sold by manufacturers.
The can of spray polyurethane should be held at an equal distance from the surface, and you should be steady when moving it across the project. Be sure to spray the surface evenly, so that there are no runs. It is important to apply several thin coats to prevent streaks. Avoid too thick a layer, as this may create an uneven finish. If a spot is too wet, you can add additional coats to create an even finish.
One of the common myths about polyurethane is that it doesn’t soak into wood. That’s simply not true. It soaks into wood regardless of how it is applied. Even though it has a higher gloss than oil-based polyurethane, it still soaks deeply into wood. This is because of capillary action, which allows water to rise to the top of a tree.
Leave a Reply
Want to join the discussion?Feel free to contribute!